Esky Belt CP

From RC Helicopter Wiki
(Redirected from Belt cp)
Jump to: navigation, search
Error creating thumbnail: Unable to save thumbnail to destination
Esky Belt CP

The Esky Belt CP is a collective pitch 450-sized helicopter that comes with a brushless motor and rate mode gyro as standard. It is available in both ready to fly and almost ready to fly form.


A number of variations are available:

  • Belt CP
The basic model.
  • Belt CP Carbon
Upgraded model with stacked carbon fibre frames, alloy head and tail, and carbon main blades.
  • Belt CP v2
New version, with heading hold gyro, 2,4GHz radio system with gyro gain control knob, and redesigned canopy.
  • Belt CP v2 Carbon
Upgraded version of the Belt CP v2, with stacked carbon fiber frames, alloy head and tail, and carbon main blades.


We have a brief guide to setting up the Belt CP with the stock transmitter.

Known issues

The main motor will easily shred the main gear in a crash if the throttle is not closed before impact (which is to be expected). Replacement main gears are only available either together with a tail drive gear, or with the one-way bearing pre-installed, making them a relatively expensive item to replace. The HeliMax MX400 main gear is a drop in replacement that is reported to be more robust.

The idle up mode switch on the top left of the stock transmitter will cause a dangerous situation if accidentally engaged, instantly applying full power to the motor whatever the collective position. As it is engaged by pulling it forwards, it can be engaged accidentally by putting the transmitter down on an uneven surface.

The diagram in the manual showing how the tail belt drives the tail rotor is wrong. The tail belt should be twisted so that rotating the main rotor (clockwise) causes the tail blades to come up towards the front of the heli (so counterclockwise when viewed from the helicopter's right hand side (the same side the tail rotor is on)).

The Esky sticker can come partially off the main motor, creating a lot of noise and drag.

Esky went through a phase of supplying Belt CP main shafts pre-bent, making them useless for helicopter use. Aftermarket shafts are available.

Esky feathering spindles for the alloy head are only available singly, making them quite expensive to replace. Aftermarket feathering spindles are available.

There are reports that the E-flite Blade 400 feathering spindles will also fit the plastic head (edit to confirm).

The washout to flybar control arm linkage can become loose at the top, and come off in flight, reducing cyclic control authority drastically. This can be prevented by replacing the ball with a ball-with-washer, as used elsewhere on the aircraft.

The servos connect to the swashplate via bell cranks, adding slop to the controls. Some people have modified their frame to move the servos and link them directly to the swashplate.

For unknown reasons, it can sometimes be impossible to get good blade tracking.

The stock Esky gyros will not initialize unless the rudder trim is moved to the centre.

The stock transmitter does not allow the gyro gain channel value to be adjusted; you need to use a gyro that sets the gain via an adjustment on the gyro, like the Futaba GY240, Align RCE500, or any of the Esky gyros. It may be possible to modify the radio to allow control of the gyro gain channel by following a variation of the instructions posted here. (Please report any success). All modes of operation for this Tx are listed here - unfortunately it's not possible to make Channel 5 proportional AND keep CCPM mixing.

For unknown reasons, the swashplate timing can be poor, with the results of cyclic inputs occurring up to 20 degrees too late.


  • Stock servos are not good and will not last long. Tower Pro SG90 servos are almost a 'drop in' upgrade, just requiring the flash around the servo holes to be trimmed off. Hitec servos (in particular) rotate the 'wrong way' to work with the stock transmitter.
  • Align blades (particularly their wooden blades) can be used, using the plastic blade roots from the Esky blades as blade grip spacers.


The following items are prone to breaking in crashes:

External links

Share your opinion